Gravesend
Boiler servicing and repairs in Gravesend
An annual boiler service in Gravesend is £90, and a repair starts with finding the cause rather than fitting the part the fault code names. We are Gas Safe registered and OFTEC certified, based in Bearsted, covering Gravesend, Northfleet and the DA11 to DA13 villages.
Your annual boiler service
A boiler service is £90, carried out by a Gas Safe registered engineer, covering the combustion and efficiency checks and a full health check of the boiler. It is also what keeps a manufacturer's warranty valid, since most makers ask for one every year. Where a boiler is limping rather than broken, a service is often the better first spend, because it finds the thing that is about to fail while it is still cheap.
Most of Gravesend runs on mains gas. Across Gravesham 9% of homes are off the gas grid, going by the government's figures, and for those we service oil boilers under our OFTEC certification and LPG boilers under our Gas Safe registration. The annual service is included in every one of our cover plans, if you would rather spread it monthly.
If you let a property, one household in five across Gravesham rents privately (19%, Census 2021). A service and the annual landlord gas safety check are separate pieces of work, usually done in one visit but recorded as two, because the check is a legal duty rather than maintenance.
Why boiler fault codes mislead
Most boiler repairs come down to a handful of faults, and the code on the display is the least reliable part of the diagnosis. A boiler has a small number of sensors and it reports what they see. When the pressure sensor reads low, the boiler says low pressure, because that is all it knows. It has no way of telling you whether that is a leak under a floor, an expansion vessel that has lost its charge, a relief valve quietly passing water out through a pipe on an outside wall, or the sensor itself misreading.
Reading the fault code and then testing the component it points at works better than simply replacing that component, because a code reports what the boiler noticed rather than what caused it, and a low pressure code has several possible causes upstream of the sensor reporting it.
This is why a boiler can have the same part fitted twice in two winters. The part was not faulty either time, it was reporting a problem that was never found. If yours keeps losing pressure after a repair, the repair addressed the message rather than the cause.
Four common boiler faults
Ignition lockout is the winter classic. The boiler tries to light, fails a set number of times and stops. It is often a condensate pipe frozen or silted rather than anything to do with ignition at all, which is why it arrives in a cold snap and why the fix is sometimes a few minutes of work.
Heating but no hot water, or hot water but no heating, points at the diverter valve on a combi rather than at the burner. No heat at all with the boiler apparently running usually points at a pump or a motorised valve. And a boiler that fires then stops within a minute or two is normally either overheating against a scaled or blocked heat exchanger, or short of gas at full rate, which is a supply question rather than a boiler one.
What to try before you call
Some faults are things you can settle yourself in five minutes, and it is better to know that before paying anybody to find out.
- Check the pressure gauge. On or near zero and the boiler will not fire at all, so topping it back up gets the heating going, though a system that needed topping up has a reason for it that has not gone away.
- Check whether it has locked out, and reset it once. Most boilers restart. One that locks out again immediately is telling you something and should not be reset over and over.
- In cold weather look at the condensate pipe outside. Frozen is common, and thawing it gently with warm water, never boiling, often clears the fault completely.
- Check the room thermostat. Flat batteries in a wireless thermostat look exactly like a dead boiler from inside the house, and they catch people out every winter.
What not to do is keep resetting a boiler that keeps locking out, or take the front off it to have a look. A lockout is a safety function doing its job, and everything behind the casing is gas work.
What Gravesend housing adds to it
19% of homes in Gravesham were built before 1919, going by the Valuation Office Agency's figures, and the older terraces in Gravesend and Northfleet frequently had back boilers originally. When they were modernised the new appliance went wherever the flue could be made to work rather than wherever suited. That leaves long pipe runs, awkward condensate routes and, often enough, a gas supply that was adequate for the old appliance and is marginal for the new one.
The post-war estates are the opposite and more useful. Rows of identical houses were built with identical layouts, so they throw identical faults, and once a condensate route or a gas run has been traced in one house, it has effectively been traced along the street. That turns an hour of investigation into a much shorter one, and it is one of the genuine advantages of using somebody who already works the area rather than a national booking service sending whoever is nearest.
Hard water, and what it does to a repair bill
North Kent is a hard water area, and it changes which repairs come up. On a combi the plate heat exchanger scales until the hot water goes lukewarm and the boiler starts overheating on the heating side. On any system, scale and sludge together are what block the narrow waterways in a modern heat exchanger, which power flushing clears.
The practical point is that a repair which does not address the water is a repair with a return date. Fitting a new part into a system full of the thing that killed the last one is not a fix, and a magnetic filter costs a fraction of the component it protects.
What a repair visit should cover
A diagnostic visit is not somebody reading a code off the front and going to the van for a part. It is a sequence, and it ends with a component rather than beginning with one.
You get told what the fault is, what it costs and whether it is worth doing on that appliance, before anything happens.
When a repair stops being the answer
Some boilers are worth repairing almost indefinitely and some are not, and the deciding factors are what the repair costs against what the appliance is worth, whether the parts are still made, how many faults it has thrown lately, and how it measures at the flue. Age is the weakest signal of the four, though it is the one most often quoted at people.
If we think you are about to spend good money on a bad appliance we will say so before taking the work, and quote for a new boiler from £1,850 if that is the better answer. If a boiler somebody has condemned has years left in it, we will say that too.
We cover Gravesend, Northfleet and the DA11 to DA13 villages from Bearsted, with free home visits and free quotes across Kent. To book a service, or if your boiler has stopped or keeps stopping, get in touch.
Book a visit in Gravesend
Calum Long is a Gas Safe registered, OFTEC certified engineer based in Bearsted, with free home visits and free quotes across Kent.
Guides
Guides on boiler servicing and repair
Why Has My Boiler Locked Out
A lockout means the boiler detected something and shut itself down deliberately. Reset it once. If it locks out again, the reason is still there, and resetting past it is the expensive mistake.
Read more →Signs Your Hot Water Cylinder Is Failing
Cylinders rarely fail without warning. What discoloured water, lost capacity, noise and a warm cupboard each point to, and the one check that tells you whether the cylinder is even involved.
Read more →Vented or Unvented Cylinder
A vented cylinder takes its pressure from a tank in the loft. An unvented takes it from the main. Which suits your house, and why only one of them is notifiable work.
Read more →
Free estimates
Get your free estimate
Call, text or email: free home visits and free quotes across Kent.
